He’s All That Anniversary!

He’s All That Anniversary

All images © 1990-2022 Stampin’ Up!®

Oh My. Isn’t the colour combo perfect for a masculine card! 

Love it!

And VW is definitely a classic. 

They were so popular back in the 80’s 

Did ya have one or did your ride around in one?

Me, my first car was a second hand Toyota Corella. It was yellow and a four door. 

Not the fanciest but it got me around. It lasted for 10 years and I only paid a grand for it.

Best money I ever spent! 

Supplies:

• Stamp Sets: He’s All That (159071)

• Card Stock and Paper: Soft Suede Cardstock (115318); Calypso Coral Cardstock (122925); Pool Party Cardstock (122924); Very Vanilla Cardstock (101650); Happy Forest Friends Designer Series Paper (158941)

• Stamp Pads & Ink: Soft SuedeClassic Stampin’ Pad (147115); Versamark Ink (102283); Pool Party Stampin’ Blends Combo Pack (154984); So Saffron Stampin’ Blends Combo Pack (154905); Calypso Coral Stampin’ Blends Combo Pack (154881); Smoky Slate Stampin’ Blends Combo Pack (154904)

• Tools: All That dies (159078); Teacup dies (160186); Paper Snips Scissors (103579); Stampin’ Cut & Emboss Machine (149653); Heat Tool (129053)

• Miscellaneous: Stampin’ Dimensionals (104430); Stampin’ Seal (152813); Multipurpose Liquid Glue (110755); Early Espresso Faux Suede Trim (152472); Stampin’ Emboss Powder-Basics (155554)

 

Measurements:

 

• Soft Suede cardstock: 8 ½” x 5 ½” (score at 4 ¼”); 4” x 5 ¼”; small scrap for die cutting

• Very Vanilla cardstock: scrap for die cutting

• Pool Party cardstock: ½” x 5 ¼”

• Calypso Coral cardstock:  ½” x 5 ¼”

• Happy Forest Friends DSP:  ½” x 5 ¼”

• Early Espresso Faux Suede Trim: 2 pieces approx. 3 ½” each

 

Instructions:

 

1. Fold the larger piece of Soft Suede cardstock in half to create the card base.

2. On the Soft Suede card layer, using Stampin’ Seal to stick the strips of cardstock/DSP on. Start with Pool Party ¾” from the bottom of the Soft Suede cardstock. Then stick the DSP above the Pool Party cardstock and then finally the Calypso Coral cardstock above the DSP.

3. Use Stampin’ Seal to stick the card layer on to the card base.

4. On a scrap of Very Vanilla cardstock, stamp the “Together for the long haul…” stamp from the He’s All That set with Soft Suede ink. Sprinkle clear embossing powder over it, tap off the excess and heat with the Heat Tool until the powder is melted (shiny & raised)

a. Tip: Ink the stamp with Versamark, then with Soft Suede ink, then stamp it on the cardstock before embossing.

5. Colour the little van with Stampin’ Blends

a. Van-Pool Party

b. Surfboard-So Saffron

c. Tires-Smoky Slate

d. Side Stripes-Calypso Coral

6. Using a Stampin’ Cut & Emboss Machine and the All That dies, die cut out the stamped image with the scallop circle die.

7. Right of center on the card layer, stick the two ribbons down in an X shape on the stripes of cardstock/DSP (use Stampin’ Seal). Stick the stamped/die cut image over the middle of the ribbon X with Stampin’ Dimensionals. Trim the ends of the ribbon if needed.

8. With a small scrap of Soft Suede cardstock, die cut out three little hearts with the smallest hearts die from the Teacup dies. Use Multipurpose Liquid Glue to stick the hearts around the stamped image (two to the top right of it and one to the bottom left)